| Assembly No.: | 1061-A-TPO SW AD |
| Assembly Owner: | Carlisle |
| Reference link: |
| Security Factor | Observed On Test |
|---|---|
| -1.7 KPA ( -35 PSF ) | -2.5 KPA ( -52 PSF ) |
| Roof System | System Type | Deck Type |
|---|---|---|
| MONO | PARS | Steel |
| Carlisle | TPO Spectro-Weld |
|---|
| Attachment Pattern | |||
| Carlisle | Bonding Adhesive AQUA-Base 120 | Adhered | |
| Carlisle | TPO Bonding adhesive | Adhered | |
| Carlisle | Low VOC Bonding adhesive 1168 | Adhered | |
| Carlisle | TPO Sure-Weld 1.1 mm to 2.1 mm (45 mil to 80 mil) |
|---|
| Attachment Pattern | |||
| Carlisle | TPO Bonding adhesive | Adhered | |
| Carlisle | Low VOC Bonding adhesive 1168 | Adhered | |
| Carlisle | Bonding Adhesive AQUA-Base 120 | Adhered | |
| Carlisle | TPO Sure-Weld Extra 1.1 mm to 2.1 mm (45 mil to 80 mil) |
|---|
| Attachment Pattern | |||
| Carlisle | Low VOC Bonding adhesive 1168 | Adhered | |
| Carlisle | TPO Bonding adhesive | Adhered | |
| Carlisle | Bonding Adhesive AQUA-Base 120 | Adhered | |
| Hunter Panels | H-Shield 25mm (1’’) à 203.2 mm (8’’) |
|---|
| Attachment Pattern | |||
| Generic |
#12 pre-assembled 3" plates
1 screw/vis per/par .372 m2 (4' ca.)
|
Mechanically Attached | |
| Hunter Panels | H-Shield CG 25mm (1’’) à 203.2 mm (8’’) |
|---|
| Attachment Pattern | |||
| Generic |
#12 pre-assembled 3" plates
1 screw/vis per/par .372 m2 (4' ca.)
|
Mechanically Attached | |
| Hunter Panels | H-Shield HD Composite 25mm (1’’) à 203.2 mm (8’’) |
|---|
| Attachment Pattern | |||
| Generic |
#12 pre-assembled 3" plates
1 screw/vis per/par .372 m2 (4' ca.)
|
Mechanically Attached | |
| Carlisle | Polyiso HP-H 25mm (1’’) à 203.2 mm (8’’) |
|---|
| Attachment Pattern | |||
|
#12 screw with round insulation plates 3"
1 screw per 0.372 m2 (4 ft.sq.)
|
Mechanically Attached | ||
| Carlisle | SecurShield 25mm (1’’) à 203.2 mm (8’’) |
|---|
| Attachment Pattern | |||
| Generic |
#12 pre-assembled 3" plates
1 screw/vis per/par .372 m2 (4' ca.)
|
Mechanically Attached | |
| Carlisle | SecurShield HD Composite 25mm (1’’) à 203.2 mm (8’’) |
|---|
| Attachment Pattern | |||
| Generic |
#12 pre-assembled 3" plates
1 screw/vis per/par .372 m2 (4' ca.)
|
Mechanically Attached | |
| Generic | Polyethylene .15 mm(6 mil.) |
|---|
| Attachment Pattern | |||
| Generic | Loose laid / en indépendance | Independance | |
| Georgia-Pacific Gypsum | DensDeck 1200 mm x 2440 mm x 12.7 mm (4' x 8' x 1/2") |
|---|
| Attachment Pattern | |||
| Generic | Loose laid / en indépendance | Independance | |
| Generic | See manufacturer / Voir manufacturier | Adhered | |
| Generic | See manufacturer / Voir manufacturier | Mechanically Attached | |
| Georgia-Pacific Gypsum | DensDeck Prime 1200 mm x 2440 mm x 6.4 mm (4' x 8' x 1/4") |
|---|
| Attachment Pattern | |||
| Generic | Loose laid / en indépendance | Independance | |
| Generic | See manufacturer / Voir manufacturier | Adhered | |
| Generic | See manufacturer / Voir manufacturier | Mechanically Attached | |
| Generic | Gypsum roof board (1.22 m x 2.44 m 15.9 mm (4 ft x 8 ft x 5/8 in.)) |
|---|
| Attachment Pattern | |||
| Generic | Loose laid / en indépendance | Independance | |
| Generic | See manufacturer / Voir manufacturier | Adhered | |
| Generic | See manufacturer / Voir manufacturier | Mechanically Attached | |
| CGC/USG | Securock Gypsum Fiber Roof Board 6.3 mm (1/4") - 17.9 mm (5/8") |
|---|
| Attachment Pattern | |||
| Generic | Loose laid / en indépendance | Independance | |
| Generic | See manufacturer / Voir manufacturier | Adhered | |
| Generic | See manufacturer / Voir manufacturier | Mechanically Attached | |
| Generic | Steeldeck 22g. Galvanized |
|---|
| Attachment Pattern | |||
|
.76 mm (0.03") - yield/âme 230 MPa (33ksi) - tensile/résistance 310 MPa (45 ksi)
Minimum resistance (CSA S136.F04) - 2.09 kN (470 pf)
|
Mechanically Attached | ||
The Central roofing reference did not realize any kind of tests and the results mentioned here, either it has carried out checks for accuracy. It offers no guarantee in that regard.
Each issued resistance result represents a specific assembly of a dynamic test laboratory ISO 17025 recognized and accredited according to the requirements of CSA A123.21.
The results should be read, seen and used in their entirety without any changes or substitutions of products or methods.
For equity products, no substitution or other change can not be done without a rigorous analysis according to specific requirements and validated by the Central roofing reference.
The optional products are optional; they do not affect in any way the result insofar as the anchor method is followed.
All terms used in this document such as "Ribbons" are terms that are part of the product technical reference and use in standard testing studied.
All the assembly data represent dynamic test results of roofing systems assembly; the assembly sheets are valid as per the manfacturer technical department keep those active and or, re-evaluations are planned to revise from the original date of the test.
It must be calculating -0.1 kPa (-0.015 psi) as the weaker result, everything bellows like -0.2 kPa (-0.03 psi) are stronger uplift wind resistance.
The Central Roofing Reference can not be held liable for any claim by the manufacturer in relation to the identification and CSA reserves the right to remove without notice and the specifications of the assembly.
This technical data assembly sheet is produce by Central Roof Reference, with copyright and subject to the Quebec legislation. All readers of this data sheet must insure themselves that she’s up to date and that she’s wasn’t avoid nether replace by a recent one. To validate, you must consult the Central Roof Reference website http://www.crt-csa.ca or to communicate with us by mail at info@crt-csa.ca
