Product Manufacturer Results Reset Search


1297-A-POWERply - Endure Bio+gravel wood - TGFY7.R6692 - #32-34

Assembly Owner: Tremco

Terms and Conditions

The Central roofing reference did not realize any kind of tests and the results mentioned here, either it has carried out checks for accuracy. It offers no guarantee in that regard.

Each issued resistance result represents a specific assembly of a dynamic test laboratory ISO 17025 recognized and accredited according to the requirements of CSA A123.21.

The results should be read, seen and used in their entirety without any changes or substitutions of products or methods.

For equity products, no substitution or other change can not be done without a rigorous analysis according to specific requirements and validated by the Central roofing reference.

The optional products are optional; they do not affect in any way the result insofar as the anchor method is followed.

All terms used in this document such as "Ribbons" are terms that are part of the product technical reference and use in standard testing studied.

All the assembly data represent dynamic test results of roofing systems assembly; the assembly sheets are valid as per the manfacturer technical department keep those active and or, re-evaluations are planned to revise from the original date of the test.

It must be calculating -0.1 kPa (-0.015 psi) as the weaker result, everything bellows like -0.2 kPa (-0.03 psi) are stronger uplift wind resistance.

The Central Roofing Reference can not be held liable for any claim by the manufacturer in relation to the identification and CSA reserves the right to remove without notice and the specifications of the assembly.

This technical data assembly sheet is produce by Central Roof Reference, with copyright and subject to the Quebec legislation. All readers of this data sheet must insure themselves that she’s up to date and that she’s wasn’t avoid nether replace by a recent one. To validate, you must consult the Central Roof Reference website http://www.crt-csa.ca or to communicate with us by mail at info@crt-csa.ca

Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.
Generate The PDF

Minimal Pressure Rate

Security Factor Observed On Test
-1.9 KPA ( -40 PSF ) -2.9 KPA ( -60 PSF )

Assembly Characteristics

Roof System System Type Deck Type
BIC MARS Wood

Assembly Specifications

Cap Sheet Membrane (Required)

Tremco BURmastic Composite Ply HT
Attachment Pattern
Tremco BURmastic Composite Ply HT Green
Attachment Pattern
Tremco BURmastic Composite Ply Premium
Attachment Pattern
Tremco BURmastic Composite Ply Premium Green
Attachment Pattern
Tremco BURmastic Supreme Composite Ply
Attachment Pattern
Tremco POWERply 300 FR
Attachment Pattern
Tremco POWERply 300 Smooth
Attachment Pattern
Tremco POWERply Endure 100 FR
Attachment Pattern
Tremco POWERply Endure 200 FR
Attachment Pattern
Tremco POWERply Endure 300 FR
Attachment Pattern
Tremco POWERply Endure 300 Smooth
Attachment Pattern
Tremco POWERply Endure 320 FR
Attachment Pattern
Tremco POWERply Endure 320 Smooth
Attachment Pattern
Tremco POWERply Plus HT FR
Attachment Pattern
Tremco POWERply Premium FR
Attachment Pattern
Tremco POWERply Premium Smooth
Attachment Pattern
Tremco POWERply Standard
Attachment Pattern
Tremco POWERply Standard FR
Attachment Pattern
Tremco POWERply Standard FR GT24 W
Attachment Pattern
Tremco POWERply Endure Bio Adhesive
1.5 - 2.0 gal. / square
Fully Adhered
Tremco BURmastic Adhesive
2.0 -2.5 gal. / square
Fully Adhered
Tremco POWERply Standard Cold Adhesive
2.0 gal. / square
Fully Adhered

Base Sheet Membrane (Required)

Tremco POWERply Heavy Duty Base
Attachment Pattern
Trufast #15 EHD with 2.4'' Barbed Metal Seam Plate
Space / espacé 9'' or 12'' o.c./ c.c. Side laps are sealed POWERply Endure Bio 60'/gal.
Mechanically Attached

Cover Board (Optional)

BP Canada Corp. BP ESGARD HD roof Insulator 6 sides
Attachment Pattern
Georgia-Pacific Gypsum DensDeck 1200 mm x 2440 mm x 12.7 mm (4' x 8' x 1/2")
Attachment Pattern
Georgia-Pacific Gypsum DensDeck Prime 1200 mm x 2440 mm x 6.4 mm (4' x 8' x 1/4")
Attachment Pattern
National Gypsum DEXcell FA Glass Mat Roof Board
Attachment Pattern
Georgia-Pacific Gypsum SECUROCK Glass-MAt Roof Board
Attachment Pattern
CGC/USG Securock Gypsum Fiber Roof Board 6.3 mm (1/4") - 17.9 mm (5/8")
Attachment Pattern
Blue Ridge Fiberboard inc. StructoDek HD Fiberboard roof Insulation
Attachment Pattern
Blue Ridge Fiberboard inc. Strudy-Dek Asphaltic Coverboard, min. 1/8''
Attachment Pattern
Rockwool Top Rock DD
Attachment Pattern
Rockwool Top Rock DD Multifix
Attachment Pattern
Rockwool Top Rock DD Plus, minimum 2'' thick/épaisseur
Attachment Pattern
Generic #12 pre-assembled 3" plates
1 fastener / ancrage 6.4 f.s/pi.ca - (5 fasteners x 4' x 8')
Mechanically Attached

Base Insulation (Required)

Atlas Roofing AC Foam II 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Atlas Roofing AC Foam III 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Johns Manville ENRGY 3 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Johns Manville ENRGY 3 AGF 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Johns Manville ENRGY 3 CGF 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Hunter Panels H-Shield 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Hunter Panels H-Shield CG 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
IKO Industries Ltd. ISO 95+ GL 25mm (1") à 203,2 mm (8")
Attachment Pattern
Rockwool MonoBoard Plus
Attachment Pattern
Rmax inc. Multi-Max FA-3
Attachment Pattern
Tremco Trisotech
Attachment Pattern
Tremco Trisotech CGF
Attachment Pattern
Tremco Trisotech G
Attachment Pattern
Generic #12 pre assembled with 3" plates
1 fastener / ancrage per 6.4 ft.sq / pi.ca. (5 fasteners x 4' x 8')
Mechanically Attached

Vapor Barrier (Optional)

Tremco AVC Membrane
Attachment Pattern
Generic Self-Adhered / Auto collante
Adhered
Generic Kraft paper
Attachment Pattern
Generic Polyethylene .15 mm(6 mil.)
Attachment Pattern
Generic Loose laid / en indépendance
Independance
Generic See manufacturer / Voir manufacturier
Adhered
Generic See manufacturer / Voir manufacturier
Mechanically Attached

Thermal Barrier (Optional)

Generic Any UL Classified any Thickness
Attachment Pattern

Decking (Required)

Generic APA Rated Plywood min. 19/32''
Attachment Pattern

Surfacing (Required)

Generic Any roofing coating
Attachment Pattern
Generic See manufacturer / Voir manufacturier
Fully Adhered
Generic Gravel / Gravier
Attachment Pattern
Generic Asphalt oxyded
Minimum 400 lbs / 100f.s. / pi.ca.
Fully Adhered
Tremco THERMastic 80
Minimum 400 lbs / 100f.s. / pi.ca.
Fully Adhered
Tremco BURmastic Adhesive
Minimum 400 lbs / 100f.s. / pi.ca.
Fully Adhered
Tremco BURmastic Adhesive SF A
Minimum 400 lbs / 100f.s. / pi.ca.
Fully Adhered
Generic White Marble Gravel 1/4''
Attachment Pattern
Tremco BURmastic ROCK-IT (white)
5.0 gal./square
Fully Adhered

Ply Sheet (Optional)

Tremco BURmastic Composite Ply HT
Attachment Pattern
Tremco BURmastic Composite Ply HT Green
Attachment Pattern
Tremco BURmastic Composite Ply Premium
Attachment Pattern
Tremco BURmastic Composite Ply Premium Green
Attachment Pattern
Tremco BURmastic Supreme Composite Ply
Attachment Pattern
Tremco POWERply 300 Smooth
Attachment Pattern
Tremco POWERply Endure 100 Smooth
Attachment Pattern
Tremco POWERply Endure 200 Smooth
Attachment Pattern
Tremco POWERply Endure 300 Smooth
Attachment Pattern
Tremco POWERply Endure 320 Smooth
Attachment Pattern
Tremco POWERply Heavy Duty Base
Attachment Pattern
Tremco POWERply Premium Smooth
Attachment Pattern
Tremco POWERply Standard Smooth
Attachment Pattern
Tremco POWERply Endure Bio Adhesive
1.5 - 2.0 gal. / square
Fully Adhered
Tremco BURmastic Adhesive
2.0 - 2.5 gal. / square
Fully Adhered
Tremco POWERply Standard Cold Adhesive
2.0 - 2.5 gal. / square
Fully Adhered
Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.
Generate The PDF