Product Manufacturer Results Reset Search


1437-A -MP-5,6,7,8 - MULTI - Mod Bit - AD12 - FM10

Assembly Owner: Johns Manville

Terms and Conditions

The Central roofing reference did not realize any kind of tests and the results mentioned here, either it has carried out checks for accuracy. It offers no guarantee in that regard.

Each issued resistance result represents a specific assembly of a dynamic test laboratory ISO 17025 recognized and accredited according to the requirements of CSA A123.21.

The results should be read, seen and used in their entirety without any changes or substitutions of products or methods.

For equity products, no substitution or other change can not be done without a rigorous analysis according to specific requirements and validated by the Central roofing reference.

The optional products are optional; they do not affect in any way the result insofar as the anchor method is followed.

All terms used in this document such as "Ribbons" are terms that are part of the product technical reference and use in standard testing studied.

All the assembly data represent dynamic test results of roofing systems assembly; the assembly sheets are valid as per the manfacturer technical department keep those active and or, re-evaluations are planned to revise from the original date of the test.

It must be calculating -0.1 kPa (-0.015 psi) as the weaker result, everything bellows like -0.2 kPa (-0.03 psi) are stronger uplift wind resistance.

The Central Roofing Reference can not be held liable for any claim by the manufacturer in relation to the identification and CSA reserves the right to remove without notice and the specifications of the assembly.

This technical data assembly sheet is produce by Central Roof Reference, with copyright and subject to the Quebec legislation. All readers of this data sheet must insure themselves that she’s up to date and that she’s wasn’t avoid nether replace by a recent one. To validate, you must consult the Central Roof Reference website http://www.crt-csa.ca or to communicate with us by mail at info@crt-csa.ca

Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.
Generate The PDF

Minimal Pressure Rate

Security Factor Observed On Test
-1.8 KPA ( -36.7 PSF ) -2.6 KPA ( -55 PSF )

Assembly Characteristics

Roof System System Type Deck Type
BIC PARS Steel

Assembly Specifications

Cap Sheet Membrane (Required)

Johns Manville DynaGlas
Attachment Pattern
Generic See manufacturer / Voir manufacturier
See refered link PRI report / MP-5,6,7,8
Fully Adhered
Johns Manville DynaGrip Base P/SA
Attachment Pattern
Generic Self-Adhered / Auto collante
See refered link PRI report / MP-5,6,7,8
Fully Adhered
Johns Manville DynaWeld Cap 250
Attachment Pattern
Generic See manufacturer / Voir manufacturier
See refered link PRI report / MP-5,6,7,8
Welded

Base Sheet Membrane (Required)

Johns Manville DynaGrip Base SD/SA
Attachment Pattern
Generic Self-Adhered / Auto collante
See refered link PRI report / MP-5,6,7,8
Fully Adhered
Johns Manville DynaLastic 180
Attachment Pattern
Generic Torched-Applied / Thermosoudé
See refered link PRI report / MP-5,6,7,8
Welded

Cover Board (Required)

Johns Manville DensDeck Prime
Attachment Pattern
Generic See manufacturer / Voir manufacturier
See refered link PRI report / MP-5,6,7,8
Adhered

Upper Insulation (Required)

Johns Manville ENRGY 3 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Generic See manufacturer / Voir manufacturier
See refered link PRI report / MP-5,6,7,8
Mechanically Attached

Base Insulation (Optional)

Johns Manville ENRGY 3 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Generic See manufacturer / Voir manufacturier
See refered link PRI report / MP-5,6,7,8
Independance

Vapor Barrier (Required)

Johns Manville JM Vapor Barrier SA
Attachment Pattern
Generic Self-Adhered / Auto collante
See refered link PRI report / MP-5,6,7,8
Fully Adhered

Decking (Required)

Generic Steel min. 22 MSG and min. yield strength 40 ksi
Attachment Pattern

Ply Sheet (Optional)

Johns Manville DynaGlas
Attachment Pattern
Generic See manufacturer / Voir manufacturier
See refered link PRI report / MP-5,6,7,8
Fully Adhered
Johns Manville DynaLastic 180
Attachment Pattern
Generic Torched-Applied / Thermosoudé
See refered link PRI report / MP-5,6,7,8
Welded
Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.
Generate The PDF