Assembly Search / Details

The Central roofing reference did not realize any kind of tests and the results mentioned here, either it has carried out checks for accuracy. It offers no guarantee in that regard.

Each issued resistance result represents a specific assembly of a dynamic test laboratory ISO 17025 recognized and accredited according to the requirements of CSA A123.21.

The results should be read, seen and used in their entirety without any changes or substitutions of products or methods.

For equity products, no substitution or other change can not be done without a rigorous analysis according to specific requirements and validated by the Central roofing reference.

The optional products are optional; they do not affect in any way the result insofar as the anchor method is followed.

All terms used in this document such as "Ribbons" are terms that are part of the product technical reference and use in standard testing studied.

All the assembly data represent dynamic test results of roofing systems assembly; the assembly sheets are valid as per the manfacturer technical department keep those active and or, re-evaluations are planned to revise from the original date of the test.

It must be calculating -0.1 kPa (-0.015 psi) as the weaker result, everything bellows like -0.2 kPa (-0.03 psi) are stronger uplift wind resistance.

The Central Roofing Reference can not be held liable for any claim by the manufacturer in relation to the identification and CSA reserves the right to remove without notice and the specifications of the assembly.

This technical data assembly sheet is produce by Central Roof Reference, with copyright and subject to the Quebec legislation. All readers of this data sheet must insure themselves that she’s up to date and that she’s wasn’t avoid nether replace by a recent one. To validate, you must consult the Central Roof Reference website http://www.crt-csa.ca or to communicate with us by mail at info@crt-csa.ca

Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.

Generate The PDF

Minimal Pressure Rate

Security Factor	Observed On Test
-2.5 KPA ( -52 PSF )	-3.7 KPA ( -78 PSF )

Assembly Characteristics

Roof System	System Type	Deck Type
MULTI	PARS	Steel

Assembly Specifications

Cap Sheet Membrane (Required)

	Tremco	Thermglass Premium Type VI

Attachment Pattern

	Tremco	Thermglass Type IV

Attachment Pattern
	Tremco	THERMastic 80 2 plies / 2 plis at 25 - 30 lbs / square	Fully Adhered

Base Sheet Membrane (Required)

	Tremco	BURmastic Composite Ply

Attachment Pattern
	Tremco	THERMastic 80	Fully Adhered

Cover Board (Required)

	ModulR TS	ProtecRSS

Attachment Pattern
	Tremco	THERMastic 80	Fully Adhered

	Rockwool	Top Rock DD Plus, minimum 2'' thick/épaisseur

Attachment Pattern

Base Insulation (Required)

	IKO Industries Ltd.	IKOTherm III

Attachment Pattern
	Tremco	THERMastic 80 2 layers of 2'' / 2 rangs de 2''	Fully Adhered

Vapor Barrier (Required)

	Tremco	AVC Membrane

Attachment Pattern
	Generic	Self-Adhered / Auto collante	Adhered

Thermal Barrier (Required)

	CGC/USG	Securock Gypsum Fiber Roof Board 6.3 mm (1/4") - 17.9 mm (5/8")

Attachment Pattern
	Generic	#12 pre assembled with 3" plates 8 screws and plates by 4' x 8' board, maximum of 12'' from each corner / 8 vis et plaquettes par panneaux de 4' x 8' avec un maximum de 12' de chaque coins'	Mechanically Attached

Decking (Required)

	Generic	Steeldeck 22g. Galvanized

Attachment Pattern
		.76 mm (0.03") - yield/âme 230 MPa (33ksi) - tensile/résistance 310 MPa (45 ksi) Minimum resistance (CSA S136.F04) - 2.09 kN (470 pf)	Mechanically Attached

Surfacing (Required)

	Generic	Gravel / Gravier

Attachment Pattern
	Tremco	THERMastic 80 25 - 30 lbs / square	Fully Adhered
	Tremco	BURmastic ROCK-IT (white) 5.0 gal. / square	Fully Adhered