Product Manufacturer Results Reset Search


1254-A-POWERply - CA12-6 - TGFY7 - #6

Assembly Owner: Tremco

Terms and Conditions

The Central roofing reference did not realize any kind of tests and the results mentioned here, either it has carried out checks for accuracy. It offers no guarantee in that regard.

Each issued resistance result represents a specific assembly of a dynamic test laboratory ISO 17025 recognized and accredited according to the requirements of CSA A123.21.

The results should be read, seen and used in their entirety without any changes or substitutions of products or methods.

For equity products, no substitution or other change can not be done without a rigorous analysis according to specific requirements and validated by the Central roofing reference.

The optional products are optional; they do not affect in any way the result insofar as the anchor method is followed.

All terms used in this document such as "Ribbons" are terms that are part of the product technical reference and use in standard testing studied.

All the assembly data represent dynamic test results of roofing systems assembly; the assembly sheets are valid as per the manfacturer technical department keep those active and or, re-evaluations are planned to revise from the original date of the test.

It must be calculating -0.1 kPa (-0.015 psi) as the weaker result, everything bellows like -0.2 kPa (-0.03 psi) are stronger uplift wind resistance.

The Central Roofing Reference can not be held liable for any claim by the manufacturer in relation to the identification and CSA reserves the right to remove without notice and the specifications of the assembly.

This technical data assembly sheet is produce by Central Roof Reference, with copyright and subject to the Quebec legislation. All readers of this data sheet must insure themselves that she’s up to date and that she’s wasn’t avoid nether replace by a recent one. To validate, you must consult the Central Roof Reference website http://www.crt-csa.ca or to communicate with us by mail at info@crt-csa.ca

Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.
Generate The PDF

Minimal Pressure Rate

Security Factor Observed On Test
-2.3 KPA ( -47 PSF ) -3.4 KPA ( -70 PSF )

Assembly Characteristics

Roof System System Type Deck Type
BIC PARS Steel

Assembly Specifications

Cap Sheet Membrane (Required)

Tremco POWERply 300 FR
Attachment Pattern
Tremco POWERply Endure 100 FR
Attachment Pattern
Tremco POWERply Endure 200 FR
Attachment Pattern
Tremco POWERply Endure 300 FR
Attachment Pattern
Tremco POWERply Endure 320 FR
Attachment Pattern
Tremco POWERply HE FR Plus
Attachment Pattern
Tremco POWERply Plus HT FR
Attachment Pattern
Tremco POWERply Premium FR
Attachment Pattern
Tremco POWERply Standard
Attachment Pattern
Tremco POWERply Standard FR
Attachment Pattern
Tremco POWERply Standard FR GT24 W
Attachment Pattern
Tremco BURmastic Adhesive SF
on any Cap ply membrane 2.0 gal./sq
Fully Adhered
Tremco POWERply Standard Cold Adhesive
on any Cap ply membrane 2.0 gal./sq
Fully Adhered
Generic Asphalt oxyded
on any Cap ply membrane 20-40 lbs/sq
Fully Adhered
Tremco THERMastic 80
on any Cap ply membrane 25-30 lbs/sq
Fully Adhered
Tremco Thermastic 100
on any Cap ply membrane 25-30 lbs/sq
Fully Adhered

Base Sheet Membrane (Required)

Tremco Burmastic Composite Ply Green
Attachment Pattern
Tremco BURmastic Composite Ply HT
Attachment Pattern
Tremco BURmastic Composite Ply Premium
Attachment Pattern
Tremco BURmastic Composite Ply Premium Green
Attachment Pattern
Tremco BURmastic Glass Ply
Attachment Pattern
Tremco BURmastic Glass Ply 28#
Attachment Pattern
Tremco BURmastic Supreme Composite Ply
Attachment Pattern
Tremco POWERply 300 Smooth
Attachment Pattern
Tremco POWERply Endure 100 Smooth
Attachment Pattern
Tremco POWERply Endure 200 Smooth
Attachment Pattern
Tremco POWERply Endure 300 Smooth
Attachment Pattern
Tremco POWERply Endure 320 Smooth
Attachment Pattern
Tremco POWERply Heavy Duty Base
Attachment Pattern
Tremco POWERply Premium Smooth
Attachment Pattern
Tremco POWERply Standard Smooth
Attachment Pattern
Tremco BURmastic Adhesive SF
on any Base ply membrane 2.0 gal/sq
Fully Adhered
Tremco THERMastic 80
on any Base ply membrane 25-30 lbs/sq
Fully Adhered
Tremco Thermastic 100
on any Base ply membrane 25-30 lbs/sq
Fully Adhered

Cover Board (Required)

BP Canada Corp. BP ESGARD HD roof Insulator 6 sides
Attachment Pattern
Georgia-Pacific Gypsum DensDeck Prime 1200 mm x 2440 mm x 6.4 mm (4' x 8' x 1/4")
Attachment Pattern
National Gypsum DEXcell FA Glass Mat Roof Board
Attachment Pattern
CGC/USG Securock Cement Roof Board
Attachment Pattern
CGC/USG Securock Gypsum Fiber Roof Board 6.3 mm (1/4") - 17.9 mm (5/8")
Attachment Pattern
Royal Adhesives & Sealants Millenium PG-1 Pump Grade Adhesive
Continuous ribbons 6', o.c.
Adhered
Tremco Tremco LR Adhesive
Continuous ribbons 6', o.c.
Adhered
Tremco Low Rise Foam Insulation Adhesive
Continuous ribbons 6', o.c.
Adhered
Royal Adhesives & Sealants Millennium One Step
Continuous ribbons 6', o.c.
Adhered
Johns Manville SECUROCK Gypsum-Fiber Roof Board
Attachment Pattern

Upper Insulation (Required)

Atlas Roofing AC Foam II 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Atlas Roofing AC Foam III 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Tremco Trisotech CGF
Attachment Pattern
Tremco Trisotech G
Attachment Pattern
Adco Products inc. Millenium One Step Foamable adhesive
Upper layer minimum 1''thick/ rang supérieur de 1'' minimum. Ribbons / cordons 12'' o.c. / c.c.
Adhered
Tremco Low Rise Foam Insulation Adhesive
Upper layer minimum 1''thick/ rang supérieur de 1'' minimum. Ribbons / cordons 12'' o.c. / c.c.
Adhered
Royal Adhesives & Sealants Millenium PG-1 Pump Grade Adhesive
Upper layer minimum 1''thick/ rang supérieur de 1'' minimum. Ribbons / cordons 12'' o.c. / c.c.
Adhered
Tremco Tremco LR Adhesive
Upper layer minimum 1''thick/ rang supérieur de 1'' minimum. Ribbons / cordons 12'' o.c. / c.c.
Adhered

Base Insulation (Required)

Atlas Roofing AC Foam II 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Atlas Roofing AC Foam III 25mm (1’’) à 203.2 mm (8’’)
Attachment Pattern
Tremco Trisotech CGF
Attachment Pattern
Tremco Trisotech G
Attachment Pattern
Trufast Tremco # 15 EHD fastener with Tremco 3'' Metal Insulation plate
Base layer minimum 2'' / Rang inférieur minimum 2''. 1 fastener / ancrage per 2 ft.sq / pi.ca.
Mechanically Attached
Trufast Trufast # 15 EHD fastener with Trufast 3'' Metal Insulation plate
Base layer minimum 2'' / Rang inférieur minimum 2''. 1 fastener / ancrage per 2 ft.sq / pi.ca.
Mechanically Attached

Vapor Barrier (Optional)

Tremco AVC Membrane
Attachment Pattern
Generic Self-Adhered / Auto collante
Adhered
Generic Kraft paper
Attachment Pattern
Generic Polyethylene .15 mm(6 mil.)
Attachment Pattern
Generic Loose laid / en indépendance
Independance
Generic See manufacturer / Voir manufacturier
Adhered
Generic See manufacturer / Voir manufacturier
Mechanically Attached

Thermal Barrier (Optional)

Generic Any UL Classified any Thickness
Attachment Pattern

Decking (Required)

Generic Steel min. 22 MSG and min. yield strength 40 ksi
Attachment Pattern
Generic .76 mm (0.03") - yield/âme 276 MPa (40ksi) - tensile/résistance 358 MPa (52 ksi) -Minimum resistance (CSA S136.F04) - 2.09 kN (470 pf)
Mechanically Attached

Surfacing (Optional)

Generic Any roofing coating
Attachment Pattern

Ply Sheet (Optional)

Tremco BURmastic Composite Ply HT
Attachment Pattern
Tremco BURmastic Composite Ply HT Green
Attachment Pattern
Tremco BURmastic Composite Ply Premium
Attachment Pattern
Tremco BURmastic Composite Ply Premium Green
Attachment Pattern
Tremco BURmastic Glass Ply
Attachment Pattern
Tremco BURmastic Glass Ply 28#
Attachment Pattern
Tremco BURmastic Supreme Composite Ply
Attachment Pattern
Tremco POWERply 300 Smooth
Attachment Pattern
Tremco POWERply Endure 100 Smooth
Attachment Pattern
Tremco POWERply Endure 200 Smooth
Attachment Pattern
Tremco POWERply Endure 300 Smooth
Attachment Pattern
Tremco POWERply Endure 320 Smooth
Attachment Pattern
Tremco POWERply Heavy Duty Base
Attachment Pattern
Tremco POWERply Premium Smooth
Attachment Pattern
Tremco POWERply Standard Smooth
Attachment Pattern
Tremco BURmastic Adhesive
on any ply membrane 2.0 gal/sq (exept THERMglass)
Fully Adhered
Tremco BURmastic Adhesive SF
on any ply membrane 2.0 gal/sq (exept THERMglass)
Fully Adhered
Tremco POWERply Standard Cold Adhesive
on any ply membrane 2.0 gal/sq (exept THERMglass)
Fully Adhered
Generic Asphalt oxyded
on any ply membrane 20-40 lbs/sq
Fully Adhered
Tremco THERMastic 80
on any ply membrane 25-30 lbs/sq
Fully Adhered
Tremco Thermastic 100
on any Cap ply membrane 25-30 lbs/sq
Fully Adhered
Tremco Thermglass Premium Type VI
Attachment Pattern
Tremco Thermglass Type IV
Attachment Pattern
Please, checkmark the products you want and click the button to generate the pdf with your chosen products only.
Generate The PDF